Controls Technician Resume Samples

HIGH QUALITY

The best examples from thousands of real-world resumes

EXPERT APPROVED

Handpicked by resume experts based on rigorous standards

DIVERSE EXAMPLES

Tailored for various backgrounds and experience levels

Controls Technicians are building management experts who install controllers for various systems in a building. Main responsibilities of a Controls Technician are performing wiring, solving technical problems, documenting work, following project deadlines, adhering to safety standards, and making sure building systems run smoothly at all times. Resume samples in the field highlight skills like technical expertise, troubleshooting, teamwork, attention to safety, effective communication, and computer competences. Associate Degrees in electronics or building management are seen on most Controls Technician resumes.

1

Controls Technician

Performed electrical maintenance on machines that needed new sensors or equipment

  • Machine repair with pneumatics and hydraulics and sometimes scheduled maintenance
  • PLC Programming and created new programs and/or modified current programs inside a machine
  • Troubleshoot with multi meters on a circuit level to using PLC to troubleshoot a machine
Candidate Info
2
years in
workforce
2
months
at this job
Electronic Technologies
2

Machinist Mate and Radiological Controls Technician

  • Provided oversight on 157 radiological control jobs resulting in no rework.
  • Improved the audit, surveillance, and evaluation program on board the USS EMORY S LAND (AS-39).
  • Coordinated 6 audit, 32 surveillances, and 5 evaluations verifying proper control of radioactive material.
  • Tracked and coordinated corrections of over 300 material and administrative deficiencies.
Candidate Info
15
years in
workforce
3
years
at this job
3

Controls Technician

  • Construction Management Professional
  • Conducted Start-Up testing and commissioning of commercial HVAC equipment using software that was then uploaded into the Building Automation System
  • Installed low voltage and communication cabling necessary for operating the system
  • Performed test's for quality assurance and made sure all Non-conformance items were addressed and resolved by maintaining written reports and documentation
Candidate Info
5
years in
workforce
3
years
at this job
HS
High School Diploma
AAS
Electrical Engineering
4

Commercial Building Controls Technician

Systems Programmer with a focus in Electrical/Mechanical Troubleshooting and HVAC Equipment.

  • Primary duty included visiting sites and addressing customer issues in timely manner.
  • Trusted with minimal supervision to complete work safely, efficiently, and completely.
  • Scope of work included programming, computer software and hardware, low and high voltage electricity, networking, server maintenance, and mechanical devices such as actuators and pneumatics.
  • Responsible for thorough and technical reports on work completed.
  • Able to explain complex technical issues to both trained technicians and inexperienced customers.
  • Worked with technicians of other companies to facilitate smooth integration of multiple control systems
Candidate Info
12
years in
workforce
3
years
at this job
HS
High School Diploma
BS
Science & Engineering
BS
Computer Science
5

Radiological Controls Technician

Qualified HAZWOPER and Asbestos Supervisor

  • One of only two technicians qualified lockout tagout.
  • Conducting and reviewing of routine radiation, contamination and airborne surveys.
  • Responsible for ensuring proper radiological oversight during D&D operations of radiological facilities.
  • Involved in the planning of radiological work and providing recommended controls to supervision and management.
  • Provides radiological oversight of processing operations during Radiological Emergency Response drills.
Candidate Info
17
years in
workforce
3
years
at this job
BA
Nuclear Engineering Technology
BA
Bachelor of Arts
6

Controls Technician

Conduct preventative maintenance, repair, installation, commissioned and general service of HVAC automation systems (Metasys) resulting in calibrating and servicing VAV controllers (VMAs) to their efficient working condition

  • Diagnosis and repair complex electronic control systems, such as air handler controllers (FECs)
  • Test and write modifications of system software using the Controller Communication Tool (CCT) resulting in accurate programming of field devices
  • Assist with system installation of communication wiring and field devices for BAS upgrades
  • Communicate with the customer upon arrival and before leaving work site to ensure work was completed at its best and fullest to have a satisfactory outcome
Candidate Info
11
years in
workforce
10
months
at this job
HS
High School
C
Air Conditioning, Refrigeration & Heating Technology
AS
Information Systems & Technology
7

Controls Technician

Conduct preventative maintenance, repair, installation, commissioned and general service of HVAC automation systems (Metasys) resulting in calibrating and servicing VAV controllers (VMAs) to their efficient working condition

  • Diagnosis and repair complex electronic control systems, such as air handler controllers (FECs)
  • Test and write modifications of system software using the Controller Communication Tool (CCT) resulting in accurate programming of field devices
  • Assist with system installation of communication wiring and field devices for BAS upgrades
  • Communicate with the customer upon arrival and before leaving work site to ensure work was completed at its best and fullest to have a satisfactory outcome
Candidate Info
11
years in
workforce
10
months
at this job
HS
Air Conditioning
AAS
Air Conditioning
AS
Information Systems & Technology
8

Commercial Building Controls Technician

Systems Programmer with a focus in Electrical/Mechanical Troubleshooting and HVAC Equipment.

  • Primary duty included visiting sites and addressing customer issues in timely manner.
  • Trusted with minimal supervision to complete work safely, efficiently, and completely.
  • Scope of work included programming, computer software and hardware, low and high voltage electricity, networking, server maintenance, and mechanical devices such as actuators and pneumatics.
  • Responsible for thorough and technical reports on work completed.
  • Able to explain complex technical issues to both trained technicians and inexperienced customers.
  • Worked with technicians of other companies to facilitate smooth integration of multiple control systems
Candidate Info
8
years in
workforce
3
years
at this job
HS
High School Diploma
BS
Science & Engineering
BS
Computer Science
9

Electronics Controls Technician Contractor for Kelly Engineering Services

  • Provided Engineering, Design, Fabrication, Installation, and Training Technicians to facilitate and implement new automated systems and controls of equipment and machinery used in the manufacturing of contact and intra-ocular surgically implanted cataract lenses.
  • Designed, Engineered, Fabricated, and Programmed automated sterile vile filler for packaging of surgical cataract lenses and implemented machine process changes for Contact Lens Grinders to facilitate an improvement in precision of grinding, reducing scrap, and increasing production.
  • Engineering and Design for system controls for sterile filling of contact lens, and intraocular lens containers.
  • Engineer and Design system controls from conception, thru validation, to installation, and implementation.
  • Hands-on work Fabricating Control Panels, Panel Layouts, upgrading and rebuilding of automated machinery and manage projects to deliver completed machine upgrades by expected deadlines.
Candidate Info
22
years in
workforce
1
month
at this job
AS
Avionics Engineering
AS
Electronics Engineering
10

Measurement & Controls Technician III

  • Installation, operation, maintenance, calibration, troubleshooting and repair of communication, analytical, measurement, instrumentation and controls equipment.
  • Assisted with Chesapeake Contractual Separation in the Barnett South while performing technology upgrade to approximately 300 radios from 900 MHz to 450 MHz
  • Program, calibrate and repair various pneumatic and electronic instruments related to both measurement and controls.
  • Schedule witnessing of Custody Delivery Point Meter Calibration, Inspection and Sampling.
  • Responsible for the day-to-day upkeep and calibration of field measurement equipment.
  • Responsible for supporting the monthly gathering system balancing review and any variance troubleshooting of assigned geographical area.
Candidate Info
20
years in
workforce
4
years
at this job
BS
Airway Science Professional Pilot

Your Resume, Made Easy.

You are looking for your dream job and need a resume? My Perfect Resume is your solution and takes the hassle out of resume writing. Create the perfect job-worthy resume effortlessly in just a few clicks!