Electronic Engineer Resume Samples

HIGH QUALITY

The best examples from thousands of real-world resumes

EXPERT APPROVED

Handpicked by resume experts based on rigorous standards

DIVERSE EXAMPLES

Tailored for various backgrounds and experience levels

Electronic Engineers develop technology for use in various electronics systems, including mobile devices and communication systems. Example resumes for this position showcase skills like developing documentation and procedures in support of production processes and requirements to ensure compliance with environmental policies and management regulations, and conducting acceptance tests, qualifications tests, and system configurations. A bachelor's degree in engineering is mandatory for this position and should be reflected on applicants' resumes. In addition, Electronic Engineers can also take the requisite exams to acquire state licenses.

Looking for job listings? Check out our Electronic Engineer Jobs page.

Want personalized resume advice? Get a FREE Resume Review

1

Electronic Engineer

Performed installation and testing radar and radio communication system to support US Army troops.

  • Integrated actual data collected from rapid radar pulses using the Modular Adaptive Signal Sorter (MASS) Deinterleaver Tester.
  • Utilized Matlab software to simulate rapid radar pulses and compared the result from that of the MASS Deinterleaver Tester.
  • Designed and implemented interface hardware to support testing of the Single Channel Ground to Air Radio System (SINCGARS) and the ARC -164 radios.
  • Conducted research to determine technology trends on commercial available VHF/UHF radios and wrote technical documents, reports and present PowerPoint briefing monthly to the branch.
Candidate Info
8
years in
workforce
4
years
at this job
BS
Electrical Electronics Engineering
2

Electronic Engineer

Designed audio system and tone synthesizer for aircraft trainer. Designed arithmetic logic PCB (TTL).

  • Worked with team to define and design architecture and hardware for a Viterbi convolution decoder.
  • Investigated implementation of Viterbi decoder in VLSI using AMCC 3500 series gate arrays.
  • Completed the final design/checkout of digitally controlled oscillator. Wrote drivers in PLM/86, Pascal, and assembly.
Candidate Info
2
years in
workforce
2
years
at this job
Design Certificate
3

Electronic Engineer

Primary responsibility was providing the electrical / electronic engineering services to the manufacturing facilities.

  • Successfully automated three major web handling / processing production lines utilizing various PLC/DCS hardware and software platforms such as: Allen-Bradley PLC5, Siemens, and Telemecanique
  • Managed plant power distribution system (4160 V - 480 V), back-up and co-generation power, energy conservation, safety and security
  • Initiated and instituted plant-wide Electro-Static Reduction Program
  • Served a key role in the design and implementation of the water treatment facility including the setup and management of the Maximo Computerized Maintenance Management System (CMMS) program
  • Initiated corporate-wide Calibration Program for ISO 9001 Certification
  • Provided crisis troubleshooting of electrical / electronic malfunctions
Candidate Info
15
years in
workforce
3
years
at this job
BS
Electronic Engineering Technology
4

Electronic Engineer

Solely responsible for design and implementation of test boxes, test procedures, and analysis of test results for two OEM and six medical product lines.

  • Designed and implemented digital, analog circuits for manual, automated test boxes.
  • Developed and documented test software.
  • Performed failure analysis and yield enhancement analysis to support product line.
  • Executed tests on products.
  • Completed contract shipments of OEM products, and continuously improved quality and procedures for production of medical devices.
Candidate Info
4
years in
workforce
1
year
at this job
BS
Electrical Engineering
5

Electronic Engineer

Focused on design for eight out of nine high-end camera series that involved 18 different models used for scientific research.

  • Designed hardware circuit, layout, and testing for RT series second-generation cameras, which provided 36 times faster readout rate than first generation, compact size, better image quality, lower noise, and more reliability.
  • Provided circuit design, layout, and testing for Insight camera which was less expensive, more compact in size, and easier to assemble. Good performance and low price maintained highest sales from 2000 to present.
  • Built flex camera, 64 mega pixels resolution with only 4 mega pixel CCD sensor. Highly accurate voltage step control to move CCD sensor plus software data composure made camera big success. Whole camera's circuit design, prototyping, evaluation, calibration, test method setting up for production.
  • Developed whole camera circuit design, prototyping, calibration, and testing method. RT2 series camera, deep cooling (-42 degree C) CCD sensor, very low noise, good non-linearity, high image quality, which made it very competitive in world's high-end camera market.
  • Supplied circuit design, prototyping, calibration, and testing method and FPGA design for critical signal timing control, gain switch, channel switch, certain number of pixel's data binning, FIFO buffering. Insight Gigabit camera, with highest readout rate (40MHz x 2 channel), smallest size still good in linearity and noise control.
Candidate Info
30
years in
workforce
18
years
at this job
BS
Electrical Engineering
MS
Electrical And Electronic Engineering
6

Electronic Engineer

Designed and tested futuristic submarine communication antenna utilizing innovative and commercial software (Ansoft HFSS)

  • Conducted research and development of submarine communication system at various speeds and depths
  • Performed predictions, analyses, and measurements of complex structures, such as radomes, using frequency selective surface (FSS)
  • Developed models to predict the performance effectiveness of electromagnetic systems for various mission scenarios using Satellite Tool Kit (STK)
Candidate Info
6
years in
workforce
2
years
at this job
BS
Electrical Engineering
MS
Electrical Engineering
7

Electronic Engineer

Implemented a virtual training program for employees abroad for the introduction of new technology and the methods of resolving product issues

  • Coordinate repair schedules, status updates using PROCOMM data tracking system, and availability of functional units for the purpose of testing the reliability of defective repair units
  • Familiarity with the requirements of working in an ISO […] environment
  • Trained individuals toward lean manufacturing standards aimed to increase repair efficiency and the reduction of waste
  • Earned desirable reviews through customer audits for two consecutive years whereby demonstrating successful failure analysis repair procedures
  • Led a product delivery rate of 90% for a first time test pass yield for a period of three years
  • Analyze, repair, and test electronic equipment in service support of customers worldwide
Candidate Info
18
years in
workforce
8
years
at this job
AS
Electronic And Computer Engineering
BS
Operations Management
MA
Technology Management
8

Electronic Engineer

Designed and developed electronic PCB-based circuitry and electronic systems for a new Maternal/Fetal Intrapartum Monitor.

  • Selected and sourced new monitor's LCD, leading to a […] annual cost savings.
  • Completed new monitor's Altera Cyclone FPGA hardware and software development.
  • Performed hardware and software design using Freescale MCORE, 68000 microprocessors, and TI MSP430 microcontrollers.
  • Successfully completed Six-Sigma DMAIC training and testing.
Candidate Info
6
years in
workforce
2
years
at this job
BS
Electrical Engineering
9

Electronic Engineer

  • Based on a 0.25 um CMOS process, successfully designed a reliable radiation-tolerant 5 Gbps serializer, which is the fastest one in global experimental particle physics field so far. A dual-channel 8 Gbps serializer design is ongoing.
  • Proposed and implemented an innovative encoder algorithm for the serializer. This high efficient algorithm can synchronize much faster than IEEE10GBE 64b66b encoder. The design is going to be integrated in our final version chip.
  • Developed a sophisticate FPGA based bit error rate test system to test the serializer in radiation environment.
  • Implemented 8b10b encoder/decoder from scratch in FPGA for a 2.5 Gbps serializer test
Candidate Info
18
years in
workforce
9
years
at this job
BS
Physics Electronics
MS
Physics Electronics
PhD
Physics Electronics
10

Electronic Engineer

Performed an analysis of microcontroller architectures, such as Motorola and Freescale.

  • Developed and debugged software for microcontroller peripherals.
  • Documented the design, testing, and analysis for electronic circuits developed.
  • Completed a three-month training course on C and C++.
Candidate Info
10
months in
workforce
10
months
at this job
BE
Electronics
MS
Electrical Engineering

Free Professional Resume Critique

We have partnered with TopResume to bring you a FREE resume critique service. Upload your resume and within 48 hours TopResume will email you a detailed analysis of what hiring managers and automated systems think of your resume – and how to improve it.

Browse
Upload Resume File