Cfd Engineer Resume Samples

HIGH QUALITY

The best examples from thousands of real-world resumes

EXPERT APPROVED

Handpicked by resume experts based on rigorous standards

DIVERSE EXAMPLES

Tailored for various backgrounds and experience levels

CFD Engineers are mechanics experts responsible for performing CFD (Computational Fluid Dynamics) and thermal analysis. Typical duties listed on a CFD Engineer resume include solving technical issues, improving quality, assisting the design team, preparing CDS reports, taking part in team meetings, and providing design engineering services. Based on our collection of resume examples, these experts should demonstrate engineering expertise, CFD knowledge, problem solving orientation, attention to details, good communication skills, and time management. Eligible candidates usually hold a Bachelor's Degree in a relevant field like engineering.

Looking for job listings? Check out our Cfd Engineer Jobs page.

Want 2-3x more interviews (guaranteed)? Get a Professional Resume Rewrite from ZipJob

1

CFD Engineer

Design and CFD Analysis of a regenerator for a Turbo Shaft Helicopter Engine

  • Thermal analysis were done on the exhaust of a Turbo Shaft Engine, to confirm that considerable amount of heat energy is present.
  • Designed the Regenerator to recover the heat and pre-heat the compressor, taking into consideration the weight and space limitation.
  • CFD analyses were performed, and Results were compared to other regenerators.
  • It was observed that the thermal efficiency can be improved by 5% and specific fuel consumption can be reduced by 20%
Candidate Info
4
years in
workforce
8
months
at this job
BE
Aeronautical Engineering
MS
Aerospace Engineering
2

Senior CFD Engineer

Developed full vehicle CFD models for front end engine cooling and external aerodynamic simulations

  • Developed correlation for external aerodynamic simulation results with experimental data
  • Performed full vehicle external aerodynamic simulations to optimize design of various components
  • Collaborated with Honda Research in Japan to develop methodology for full vehicle thermal modeling
  • Participated in engine cooling, heat resistance and external aerodynamic testing of development vehicles
  • Assisted in training of contingent engineers and student interns in using simulation tools and software
Candidate Info
16
years in
workforce
2
years
at this job
BS
Mechanical Engineering
MS
Mechanical Engineering
3

CFD Engineer

Efficiently conducted detailed analyses of multiphase flow and heat transfer in reciprocating engine development
environments, premixers, and separators

  • Effectively designed experimental test rigs and mechanical components for model validation and calibration
  • Successfully optimized parameters of conceptual and detailed designs using ANSYS DX
  • Performed mass and energy balance calculations, created numerical performance maps and efficiency maps
  • Performed CFD study of bulk water in reciprocating compressor; Characterized possibility of hydraulic lock
  • Modeled flow of in-cylinder bulk liquid, and its flow through valves, and transient liquid flow through orifices
  • Developed custom tools and GUI's for design of experiment and testing
  • Reduced development time and saved millions using an innovative test matrix design
Candidate Info
13
years in
workforce
2
years
at this job
BA
Mechanical Engineering
MA
Flow Measurement Laboratory
PhD
Mechanical Engineering
4

CFD Engineer

Developed and implemented design modification to Emhart Glasses suite of foreharths by performing full fluid/thermal analysis using conjugate heat transfer (CHT) and radiation with Fluent software.

  • Verified simplification of burner for radiation model.
  • Established operating ranges of metering spouts for Emhart Glasses series of feeders.
  • Developed presentations for marketing of Emhart Glasses forehearth and distributor systems.
  • Established design modification of direct cooling air flow nozzle of the 340 forehearths to reduce burner entrainment resulting in improved glass conditioning.
  • Determined thermal effects of zone to zone cross-over flow of cooling air which resulted in lowering of partition.
Candidate Info
20
years in
workforce
1
year
at this job
BS
Chemical Engineering
MS
Mechanical Engineering / Engineering Science And Mechanics
5

CFD Engineer /mechanical Engineer

Performed CFD analysis of air flow dynamics to evaluate flow pattern and reduce pressure drop of the liquid desiccant air conditioning units components (coils, fan housings &, media bed shape) for a range of unit capacities (500-20,000 CFM).

  • Conducted CFD analysis for understanding the hydrodynamics and heat transfer through different components of the air conditioning units to optimize the size of heat exchangers and media beds.
  • Performed numerical simulation of heat/mass transport and distribution of aqueous two-phase flow inside the sumps of the units to reduce the energy loss using ANSYS Fluent.
  • Lead design engineers and test engineers to launch of new generation 22,500 CFM liquid desiccant air conditioning unit.
  • Assessed test results, developed correlations with experimental data and suggested corrective actions as required to optimize air flow pattern, heat/mass transfer.
  • Analyzed and negotiated design to increase the HVAC performance and reduce the cost. (Cost reduction ranged from 7% to 35% based on unit capacity).
  • Developed and maintained HVAC Bill of Materials (BOM) including component requirements and prepared CTS (component technical specification).
  • Daily collaboration with refrigeration, manufacturing and control Engineers as well as other key areas of the organization to creatively and jointly develop the overall optimal solutions.
  • Recognized the source of carry-over liquid desiccant after the media beds. The proposed modified manifold led to 40% cost reduction and 200% reduction in carry over and the proposed design was patented (SYSTEM AND METHOD FOR THE TRANSFER, DISTRIBUTION, AND RETENTION OF A FLUID IN A HEAT AND MASS EXCHANGER (pending)).
Candidate Info
11
years in
workforce
2
years
at this job
PhD
Mechanical And Aeronautical Engineering
6

Thermal/cfd Engineer

  • Designed, simulated and prototyped an Evaporative Cooling System.
  • Created 3D mesh using SolidWorks + PointWise. Simulated the behavior of microstructures in terms of pressure drop and cooling efficiency using Fluent. Developed UDF (User Defined Function) program to simulate evaporation.
  • Optimized the [company name]ometry to keep pressure drop under 1 inAq and cooling efficiency over 85%
  • Responsible for communicating between sponsor, team members and faculty advisors.
Candidate Info
1
year in
workforce
4
months
at this job
BS
Electrical And Computer Engineering
BS
Aerospace Engineering
MS
Aerospace Engineering
7

Senior CFD Engineer

Created impeller models from CAD to CFD, and developed an extensive CFD database for various impellers.

  • Performed CFD simulation of fluid flow and heat transfer associated with mechanical
  • Provided CFD supports for optimization of mixing design, and delivered technical reports to the design engineers and external customers.
  • Conducted CFD research on bioreactors, and published technical articles.
Candidate Info
18
years in
workforce
8
years
at this job
PhD
Mechanical Engineering
8

Senior CFD Engineer

  • Created impeller models from CAD to CFD, and developed an extensive CFD database for various impellers.
  • Performed CFD simulation of mixing by mechanical impellers, gas spargers and pumps.
  • Provided CFD supports for optimization of mixing design, and delivered technical reports to the design engineers and external customers.
  • Conducted CFD research on bioreactors, and published technical articles.
Candidate Info
18
years in
workforce
7
years
at this job
PhD
Mechanical Engineering
9

Senior CFD Engineer

Managed & executed CFD projects from start to end

  • Prepared estimation for projects, project plan and project deliverables
  • Managed team of two engineers to deliver high quality results in efficient manner
  • Modeled problems involving combustion, radiation & heat transfer, multiphase flows, noise & acoustics, fluid structure interaction using CFD
  • CFD in Automotive: Cabin Ventilation, Defogging, Deicing, solar load, acoustics
  • CFD in Turbo machines: Noise reduction in axial fans, centrifugal pumps, hydro turbines, fan design tool (Published CFD aided noise reduction paper at NAFEMS conference)
  • CFD in Power Generation: Modeled combustion of coal & gaseous fuels for burners, methane & hydrogen combustion in HRSG, sulfur recovery unit, electrostatic precipitator, flue gas flow analysis, dry sorbent optimization, activated carbon injection
Candidate Info
7
years in
workforce
3
years
at this job
BA
Bachelor of Arts
MA
Thermal And Fluid Science
10

CFD Engineer

Collecting all the relevant data required for a thorough analysis of the customer Data Center.

  • Investigating and addressing the thermal issues through CFD analysis.
  • Recommending air cooling solutions to maintain the Data Center under the ASHRAE standards.
  • Providing energy savings by optimal utilization of the existing system.
  • Tools used for CFD analysis are 6Sigma, TileFlow, Flotherm.
Candidate Info
9
years in
workforce
5
years
at this job
BA
Mechanical Engineering
MS
Mechanical Engineering
Via Interface

Free Professional Resume Critique

We have partnered with TopResume to bring you a FREE resume critique service. Upload your resume and within 48 hours TopResume will email you a detailed analysis of what hiring managers and automated systems think of your resume – and how to improve it.

Browse
Upload Resume File